Important note:
—————
For USB/DSD interfaces shipped after November 19, 2015 the driver version 2.26.0 has to be installed.
This also refers to INT204 interfaces with serial numbers 1181 and higher.
Download INT204 2.26.0 Windows driver / Download INT204 1.56 Windows driver
The older devices still need the version 1.56 driver, the new driver does not work with those devices.
The notes below are important for the old driver, i.e. the version 1.56 driver. The new version 2.26.0 driver should pose no problems to install.
Installing the version 1.56 driver on Windows 10
————————————————
At first do not plug in the USB device to the USB port of the computer.
1) right click on the setup.exe file of the driver
2) select “properties”
3) select the “compatibility” tab
4) check the compatibility mode checkbox and select windows 7 from the list
5) click on OK
6) double click the setup.exe file
7) allow the execution of the setup.exe program
8) plug in the USB device
9) click NEXT and continue to install
10) allow the installation despite the warning(s) which may show
Installing the version 1.56 driver on Windows 8 or 8.1
——————————————————-
To be able to install the version 1.56 driver on Windows 8 or 8.1 one has to disable the windows driver signing check. This can be done via a special windows booting option as follows:
1) If logged in as a user, log out. The log in screen appears. In the lower right corner the power on/off icon appears. Click on that icon, hold the Shift key and click on the “restart” selection.
2) Now a blue screen with some options appears, select trouble shooting at the bottom then select advanced options (or maybe extended options) at the bottom. Then select startup settings in the lower right then select restart. another screen appears which allows to select restart options. Press key 7 to select option 7) which deactivates the driver signature checking.
3) Now the windows starts again as usual, only that you can now install the USB driver w/o error message.
Proceed according to the instructions on top of this page.
***Weiss USB driver supports Windows 10. If you experiencing problem during driver installation, please install under Safe mode boot up.
重要的提示:
-----
對於2015年11月19日之後發貨的USB / DSD接口,必須安裝驅動程序版本2.26.0。
這也是指序列號為1181或更高的INT204接口。
下載INT204 2.26.0 Windows驅動程序/下載INT204 1.56 Windows驅動程序
舊序號設備仍然需要1.56版驅動程序,新驅動程序不適用於這些設備。
以下註釋對於舊驅動程序,即版本1.56驅動程序很重要。新版本的2.26.0驅動程序應該不會造成安裝問題。
在Windows 10上安裝版本1.56驅動程序
----------------
首先不要將USB設備插入計算機的USB端口。
1)右鍵單擊驅動程序的setup.exe文件
2)選擇“屬性”
3)選擇“兼容性”選項卡
4)檢查兼容模式複選框並從列表中選擇Windows 7
5)點擊確定
6)雙擊setup.exe文件
7)允許執行setup.exe程序
8)插入USB設備
9)點擊NEXT並繼續安裝
10)允許安裝,儘管可能會顯示警告
在Windows 8或8.1上安裝版本1.56驅動程序
-------------------
為了能夠在Windows 8或8.1上安裝版本1.56驅動程序,必須禁用Windows驅動程序簽名檢查。
這可以通過一個特殊的Windows啟動選項完成,如下所示:
1)如果以用戶身份登錄,請註銷。出現登錄屏幕。在右下角顯示電源開/關圖標。點擊該圖標,按住Shift鍵並點擊“重新啟動”選項。
2)現在出現一個藍屏並帶有一些選項,選擇底部的故障排除,然後選擇底部的高級選項(或者擴展選項)。然後選擇右下角的啟動設置,然後選擇重新啟動。出現另一個屏幕,允許選擇重啟選項。按下鍵7選擇選項7),該選項禁用駕駛員簽名檢查。
3)現在窗戶像往常一樣再次啟動,只是您現在可以安裝USB驅動程序不帶錯誤消息。
按照本頁上方的說明進行操作。
*** Weiss USB驅動程序支持Windows 10.如果您在安裝驅動程序時遇到問題,請在安全模式啟動下安裝。